Permit-ready drafting for Morgan Hill ADUs, additions, remodels and new homes — drawn to fit Morgan Hill's zoning, hillside and flood-zone requirements.
Morgan Hill sits at the south end of Santa Clara County, where the valley floor gives way to foothills on both sides of town. That geography shapes a lot of residential projects. Properties on the hillsides fall under the city's Hillside Combining District, which can bring a Design Permit from the Planning Division ahead of the building permit, a geotechnical survey and extra fire-safety requirements where the lot sits in a mapped fire hazard zone. On the valley floor, parcels near Llagas Creek and other local creeks may sit in a flood hazard area, which brings its own floodplain management rules, and the older neighborhoods around downtown have a different character than the newer subdivisions on the edges of town. Homeowners here are often adding an ADU for family, adding space to a larger lot, or remodeling an older home, and drawings that ignore the specific overlay or hazard zone a parcel falls into tend to draw questions from the city that a plan prepared against Morgan Hill's own checklists would address up front.
Detached, attached and junior ADU plans sited to Morgan Hill's setback, height and lot-coverage rules, prepared against the city's ADU submittal checklists with the state ADU allowances applied correctly.
Room and second-story addition drawings coordinated with Morgan Hill's zoning standards and, where they apply, the Hillside Combining District and flood hazard area requirements.
Interior and exterior remodel drawings for kitchens, baths and whole-house renovations, including scope that triggers a full plan check submittal.
Ground-up custom home drawings and garage-to-living-space conversions prepared for Morgan Hill's submittal process, including hillside and high fire-zone parcels.
We review your lot, existing structure and goals, and confirm zoning and any hillside, fire hazard or flood overlay that applies to your Morgan Hill parcel.
Full construction drawing set — site plan, floor plans, elevations, sections and details — prepared to Morgan Hill's plan content and completeness checklists.
Energy compliance and, where needed, structural and geotechnical input coordinated into the same submittal package, which matters most on sloped lots.
If the city comes back with corrections, we revise and resubmit — we don't disappear after the drawing set goes out.
Two decades drawing plans for Morgan Hill and the surrounding South Bay cities, not a generic national template.
Drawings prepared under professional design standards, not just CAD line work — useful when a project needs design review.
Fire hazard severity maps, zoning and ADU standards get updated — we check the current city requirements, not last year's.
You work directly with the person drawing your plans, from first sketch through plan check corrections.
Based in San Jose, working throughout Santa Clara, San Mateo and Alameda counties and the wider Bay Area.
It depends on the project. Many single-family ADUs, additions and remodels can be permitted with drafted plans alone, but structural elements such as retaining walls, hillside foundations and some second-story additions often call for a licensed engineer's stamp, and hillside projects generally need a geotechnical survey as part of the application. We'll tell you upfront whether your project is likely to need engineering and can coordinate it as part of the drawing package.
We can't predict the city's timeline. Turnaround depends on submittal volume, project scope and whether an extra review applies, such as a Design Permit on a hillside or flood-area parcel. What we can do is prepare a complete set against the city's checklists and respond promptly to any comments the city sends back.
Often, yes. The city's ADU page describes detached, attached, conversion and junior ADU options on single-family properties, and notes that properties in historic, hillside, high-fire, flood or other special zones may need an additional application or face limits on what can be built. State and local rules set the baseline setback, height and size limits, so we confirm what applies to your specific parcel during the site walk before we draw anything.
The Hillside Combining District is an overlay that can add a Design Permit from the Planning Division before the building permit, a geotechnical survey, and a slope determination by a licensed engineer or land surveyor. Many hillside properties also fall in a high or very high fire hazard zone, which brings additional fire-safety and wildland-urban-interface construction requirements. Check with the city's Planning Division on how the overlay applies to your parcel, and we'll build those items into the scope early.
A site address, rough scope of what you want to build, and — if it exists — a copy of your current property survey or existing floor plan. If you don't have a survey, we can help you get one.
Both, if you want it bundled. We prepare Title 24 / CF1R energy compliance documentation alongside the architectural drawings so the whole package is coordinated and submitted together — see our Title 24 & CF1R services for details.
Tell us what you're building and we'll get back to you with next steps — usually within one business day.
(408) 634-6655